Tampilkan postingan dengan label pressure washer 1200 psi. Tampilkan semua postingan
Tampilkan postingan dengan label pressure washer 1200 psi. Tampilkan semua postingan

Senin, 27 Januari 2014

is there a tank/sprayer combo with enough PSI to wash a car?

pressure washer 1200 psi on Mini Brute II 1200 psi 2.3 GPM Hot Water Electric Pressure Washer ...
pressure washer 1200 psi image



contact


I see that most tank/sprayer combos have maybe 100 PSI, which seems suited just for applying chemicals for agricultural purposes. It seems that most sprayers for car washing applications are at least 1200 PSI. I just need to be able to wash off top layers of dust and dirt and saturate a car for hand washing, but 45, 60, 100 PSI all seem a bit low to me.

Can I pull this off without purchasing a tank and a separate pressure washer?

Links would be greatly appreciated, thanks.



Answer
Go to Walmart they sell various pressure washers of different PSI. I wouldn't get over 100psi or close to that, so you don't peel paint and blow window seals.

How can you adjust the PSI from a pressure washer?




Freedom


Hello,

I am looking into purchasing a pressure washer for various uses, they are pretty affordable from what I can tell, however for a few applications I need a level of pressure around 1200, no higher. If I use any higher there may be damage done by the water. Is it possible a pressure wand can have an adjustable max pressure? Or perhaps just being careful enough to keep the nozzle far away enough?

Many pressure washers seem to be in the 1500-2000 PSI range.

Thank you.



Answer
My parents craftsmen pressure washer has a 2400psi max pressure. However the wand is adjustable so the spray can be more or less concentrated depending on what you need. Also the engine has a throttle control. "Turtle" speed makes a good bit less pressure than "rabbit" speed. Also the water loses pressure very fast once it exits the wand so just holding it back a bit will be enough. Hope this helped.




Powered by Yahoo! Answers

Senin, 29 Juli 2013

Pressure washing a wood deck?

pressure washer 1200 psi on Cat Pressure Washer | Parts for Pressure Washer
pressure washer 1200 psi image
Q. NEVER pressure washed before:

water temp?
angle of wand?
Is a chemical solution part of the process?
How much pressure, in PSI?
Then stain?
Then seal?
Do you sand at all before staining?

Thanks for any tips/hints


Answer
water temp doesn't matter
1st soak all wood to be washed with bleach/wood wash solution, using a garden sprayer (olympic makes a good deck wash, or if you have mildew, use jo-max. both are available at paint retailers)
2nd wash the surfaces. use a tip with the widest fan pattern. move the wand from side to side, and don't stop with the spray in one place, or you will damage the surface. instead,
"feather" by bending your wrist to direct the spray sideways at the end of each pass. as long as you keed the wand moving you'll be ok. practice on a 2 x 6 board, or on the side beams or support posts.
start at 1000-1200 psi. increase the pressure as you get the hang of it, to a setting that works best. some power washers have a detatchable wand so you can put the tip directly on the gun, which is much easier for rails and spindles, .be careful of splash back in corners.
let the wood dry thouroughly, 48 hours at least. staining or sealing is a matter of taste. again, olympic makes great semi transparent and solid stains. but stains can wear off in traffic areas. if you use a semi transparent, next time you would have to strip the entire deck.
if you choose to seal it, DON'T USE THOMPSONS! it contains wax which looks great and repels water wonderfully, for about six months. then it starts to discolor and show wear.
flood co. (www.flood.com) makes a product called CWF that i have found is the best out there. apply in the morning to avoid direct sunlight. use an 18 inch 1/2" nap roller on the deck itself if you have a lot of surface area, and i mini roller on the spindles and rails.
get your products and tips at your local paint store where professional painters go, rather than one of those home centers.
powerwashing this way will prep the wood for application of any product. there shouldn't be any need for sanding. good luck

Need to break my pressure washer pressure ( 3000 psi) into different level 500,1200,1800,2200, 2500,2800 psi?




adhikari_s


I am sending 3000 psi through pipe and need to break and obtain differnt psi strength at different point because I need to test my device in different psi level. Please help me to do so. Do I need to buy differnt psi checking meter or I can use valves at different check point. Kindly help me giving easy way


Answer
Since a pressure washer uses a positive displacement pump you will need to keep a flow of water through the pump.

This is done by installing a recirculating relief valve from the discharge to the inlet side of the pump.

When pressure rises above a preset limit the relief valve opens and returns some of the high pressure water back to the inlet, recirculating.

Most pressure washers come with such a pressure setting device already installed. You either need to adjust it OR it may be damaged and stuck closed.

You may also add a relief valve to the inlet of your device to protect it from over pressure and to allso testing at different pressures. Just let this valve blow off to the ground or a drain...




Powered by Yahoo! Answers