Tampilkan postingan dengan label pressure washer 2800 psi. Tampilkan semua postingan
Tampilkan postingan dengan label pressure washer 2800 psi. Tampilkan semua postingan

Minggu, 26 Januari 2014

71 elcamino 383 510-488-262duration cam 144 blower th400 msd ignition want to change gears currently 4.56?

pressure washer 2800 psi on Thorough Evaluation of the NorthStar 2800 PSI Cleaner
pressure washer 2800 psi image



mark d


Iam running about a 2000 stall pulls a little when you put it in gear want to go to a gearset that will pin you in the seat a little and get a little better gas mileage currently get about 4.5 if your easy on it. Set up with 6psi boost on 8.1-1 pistons small valve heads casting date 1970 supposed to from a camaro. Any clue on what kind of h.p. 750 edelbrock carb mandrel bent pipe,headers and flowmasters


Answer
Your 4.56's are running the engine out of breath on the top end.. That combo aint gonna make power in the higher RPMs where the 4.56's will put you crossing the traps.

You have a mild cam'ed, 383 stroker with a small blower... Your engine is making the torque.. No need to try to do it with gears.

Your best gears will probbly be 3.42's to tell you the truth.. I would need alittle more info to be 100% sure though.. Like your rear tire size, and all the specs on that 262* cam (adv. duration, duration at .050", lope sep angle)

The 4.56's you have now will "pin you in the seat" the hardest on launch than any other gear, but it's killing your top end (putting rpms past the rpm where your HP peaks at) and also killing your fuel mileage.

If it's not "pining you in the seat" now, then you have some slight probs in tuning. Or your just boiling the tires off, no traction, just spinning hard.

I would also go higher on the stall.. That combo sounds like it needs 400-800 rpm more stall.. So a 2400-2800 stall converter.

Hows your tuning?

I love the edebrock carbs. I been running them and carter AFB (same carb as edelbrock) for the past 8 years..

Out of the box they have a few probs that needs to be fix though..

If you noticed the engine trying to die during hard braking or cornering.. Or a bog when you hit the throttle..

It's the floats not adjusted right.. Out of the box most was set wrong.. You need to adjust them to 7/16" at rest, and 15/16" to 1" drop.

The pump arm linkage need to be in the top hole as well.

The other major thing with them is fuel pressure.. 5.5 psi is max the needles can handle.. Over that and the pressure bounces the needles off the seats and trys to flood carb some.. Use an adjustable fuel reg inline with supply line and set pressure to 5.0 to 5.5 psi (I run mine at 5.25)

In most performance engines the step up springs needs to be changed out too.. The 7" HG pink springs work good in alot of set ups...

You really need to get your vac level though to see what springs you need though.

Also carb jetting.. Hows yours running.. Rich, lean? Your spark plugs are the best thing to let you know.. Read your plugs and jet till plugs shows you are just right.

What spark plugs are you running? I belive 1970 chevy heads still used gasket seat, not taper seat plugs.... So you will need the spark plugs with the large 13/16" wrenching hex, not the 5/8" hex and a washer type gasket on the plugs.. If you run AC delco plugs the # with be R4-S... The blank spot is the heat range..
Most roots blown engines will need atleast 1 step colder plug.. So an R44S ac delco plug or maybe 2 steps colder R43S.

Whats your timing like? The boost will cause detonation quicker on pump fuel, so you may have to pull alittle timing out. Try 34* total to start with.

Also set your timing curve so full mech advance is fully in at 3,000 rpm

What brand and type and power level of pressure washer should I buy to clean OIL Stains off the driveway?




Gato


What brand and type and power level of pressure washer should I buy to clean OIL Stains off the driveway?

Would I need electric or gas powered? I got some tough stains on my driveway street area's that I want to clean up. My car USED to leak oil and I hate the oil stains onb the ground...They are kind of OLD stains and I tried all types of chemicals already to clean them but they didn't completely work. I want to try a pressure washer / cleaner now.

Any advice would be greatly appreciated!

Thanks in advance!



Answer
I bought a 2200 psi pressure washer a couple of years ago and I sure wish I had bought a more powerful one. I use it mostly to clean my deck and driveway.

Mine is a TroyBilt, but I don't think brand matters much.

I would suggest at least a 2800 psi or even higher.
Definitely get a gas one.
The electric ones are for girls.




Powered by Yahoo! Answers

Jumat, 29 November 2013

Need to break my pressure washer pressure ( 3000 psi) into different level 500,1200,1800,2200, 2500,2800 psi?

pressure washer 2800 psi on Thorough Evaluation of the NorthStar 2800 PSI Cleaner
pressure washer 2800 psi image



adhikari_s


I am sending 3000 psi through pipe and need to break and obtain differnt psi strength at different point because I need to test my device in different psi level. Please help me to do so. Do I need to buy differnt psi checking meter or I can use valves at different check point. Kindly help me giving easy way


Answer
Since a pressure washer uses a positive displacement pump you will need to keep a flow of water through the pump.

This is done by installing a recirculating relief valve from the discharge to the inlet side of the pump.

When pressure rises above a preset limit the relief valve opens and returns some of the high pressure water back to the inlet, recirculating.

Most pressure washers come with such a pressure setting device already installed. You either need to adjust it OR it may be damaged and stuck closed.

You may also add a relief valve to the inlet of your device to protect it from over pressure and to allso testing at different pressures. Just let this valve blow off to the ground or a drain...

How many hours can you use a pressure washer before you need to change the oil?




Kevin


I Have a 4 year old Troy-Bilt 4.5HP 2200 Psi Pressure Washer. ive recently bored out the Inflow/outflow of the pump increasing the water flow, put a high performance spark plug and put bigger jets on the carburetor. and i began using 93 octane Shell V-power Nitrogen enriched fuel. My pressure washer cleans better then my friends 2800 Psi washer. but my question is how many hours can i go until i need to change my oil, im curious because of my recent modifications im sure the motor is harder on oil.


Answer
Oil does not lose its properties, just gets dirty.That is main reason for filter on a car. Hope this helps.




Powered by Yahoo! Answers