Where to buy a sewer nozzle ?

pressure washer nozzle size image

Q. For out design at university we need a sewer nozzle type thing . Where I can order one apart from ebay ?

Answer
Pressure Washer Spray Nozzle can be identified by the nozzle "number", a four or five digit number that is stamped on the nozzle, which indicates the spray angle and orifice size. In all cases the first two digits of the nozzle number indicate the spray angle (disperse) in degrees.

EXAMPLE: 00 is 0 degree, 15 is 15 degree, 25 is 25 degree and 40 is 40 degree. The last two digits of the nozzle number indicate the orifice size, a standard industry designation. EXAMPLE: 06 is a 6.0 orifice, 55 is a 5.5 orifice. These numbers correspond to the actual dimensions, giving the size of the orifice.

They do not however directly indicate gallons per minute, flow rates or inches in diameter of the orifice. Some power washers come with an adjustable nozzle (called Vari Nozzle) that is attached to the end of the wand. The fan spray may be adjusted by turning the nozzle, chemical may also be applied by pulling out word on the nozzle. or more information click on source link.

The cons of a pressure washer?

Heather

Sand blaster/pressure washer. Besides the price?
Perhaps damage? Thanks!

Answer
Depending on the tip size and how close it is to the surface, it can peel paint, leave dark streaks on bare wood like a deck, and even peel the skin off your hand! So just keep the nozzle about a foot away from the surface and sweep back and forth evenly to get even cleaning that doesn't damage it.

Powered by Yahoo! Answers

pressure washer still doesn't pass water after inspecting check valves. What next?

pressure washer valve image

tonymonton

Check valves look fine. It's an industrial pressure washer. 7.5hp, 240v, 3phase motor and diesel burner. Previous owner reports not used in 10 years, but functioned fine then. Any ideas?
I have 3 phase power, and the electric motor runs fine.
The motor spins, but the pressure doesn't rise. I tried it 6 days ago. Only for 5 to 10 seconds, not to ruin the pump. Today, the pump check valves were dry, as well as the visible internal parts of the pumps I could see.

Answer
When turning on the unit, does it sound like the motor spins fast then loads up?? Like it is trying to build pressure?? If not water is not getting to the pump. If it is, there could be corrosion in the hose and plugging up the tip. Try removing tip and see if it works..


Is there a holding tank that the fresh water fill before the pump??? If there is there will be a float on it just like a toilet, make sure there is water in there and the float is working..

Why wouldn't a pressure washer be putting out any pressure?

Arch Bisho

I've had this pressure washer for 2 years, I just sold it and the guy says 'the pump cut out and won't come back on'. Its a 13hp Honda engine, on a 3600 psi 4gpm pump. What would cause a loss of pressure? If the pump seized, would the engine still run?
Its hooked up to a house spiket, I think it flows 6-8 gpm.

Answer
You didnt give much information as to what brand pump is mounted to the honda engine. But to venture an educated guess I would say Cam is right. The unloader valve is stuck in the unload mode. It could also be the "Easy-Start Spring" has broken and is locked in the start mode. (low pressure mode for easy starting of large horse power engines)

Powered by Yahoo! Answers

buying a power wash,how much it realy cost?

pressure washer 600 psi image

Douglas P

Hi,
I have a cleaning services business i will start also window cleaning and power wash cleaning, so a i need a power wash and my cosin has one Karcher 4000 PSI Gas Pressure Washer #G4000SH with is grate and runs and looks nice he is not using it any more and he ask me $600$ it need only a gun extension.
i look at ebay and amazon and the same machine is around $850 to $899(on sale).
i realy apreciate all help especialy from experts.

thank you!

Technical Details:Karcher 4000 PSI Gas Pressure Washer #G4000SH
4,000 psi gas-powered pressure washer with 13 hp Honda GX series engine
For heavy-duty cleaning jobs
Features high-performance commercial-grade pump with brass pump head
Includes stainless-steel wand, 50-foot hose, and full set of Quick Connect nozzles
75 pounds

thank you all

Answer
I have a cleaning business and pressure wash frequently. That sounds like a good price but make sure that the engine is Honda. I have two pressure washers and Honda will last forever. My 4000psi was 900 brand new. Good luck to you.

how much this power wash realy cost?

Douglas P

Hi,
I have a cleaning services business i will start also window cleaning and power wash cleaning, so a i need a power wash and my cosin has one Karcher 4000 PSI Gas Pressure Washer #G4000SH with is grate and runs and looks nice he is not using it any more and he ask me $600$ it need only a gun extension.
i look at ebay and amazon and the same machine is around $850 to $899(on sale).
i realy apreciate all help especialy from experts.

thank you!

Technical Details:Karcher 4000 PSI Gas Pressure Washer #G4000SH
4,000 psi gas-powered pressure washer with 13 hp Honda GX series engine
For heavy-duty cleaning jobs
Features high-performance commercial-grade pump with brass pump head
Includes stainless-steel wand, 50-foot hose, and full set of Quick Connect nozzles
75 pounds

thank you all

Answer
Why not rent an electric one for those jobs. Bet it would be cheaper in the long run.

Powered by Yahoo! Answers

Which pressure washer can receive hot water at 120 degrees?

pressure washer hot water image

d_awood

I just installed a new water heater and installed a spigot so that I could connect a pressure washer after it so I would have hot water that is soft to wash my car and for general use.

I don't want to have to purchase a pressure washer that heats the water. which pressure washers can receive hot water for the intake?

Answer
doesn't sound hot enough to be a problem for the washer if it has a brass pump, but that is hot enough to scald someone - a mixer valve were you could temper the water would be safer

making your own hot water pressure washer?

how can you heat a 110 gallon plastic resin tub to make the water hot so you have a hot water pressure washer?

Answer
you have to be careful running hot water through a preasure washer. the seals in the pump may not be rated for hot water.

Powered by Yahoo! Answers

I took apart my pressure washer pump and gear oil has spilled all over. How do I reassemble?

pressure washer with honda engine image

X-Men

I took apart my Karcher K2400HH pressure washer pump unit from the engine and now gear oil is all over on the ground. I think I took the whole pump unit out and now I need to reassemble it back again. How do I put it back together, where do I fill the oil back in and what type of gear oil should I use? Any help would be appreciated.

Answer
I had the same problem with a Generac Model No 1537 2400PSI washer.!!! This unit has a 5.5 HP Honda engine.
I'm a builder, and one of my customers gave me this pressure washer after he had problems with it. Seems he left it with the gas in it for years and gummed up the carb. He told me his daughter ran it without the water turned on and burned up the pressure pump. He bought a new pump, but had no idea how to replace it. When I removed the old pump, I had a flood of oil on the garage floor. The new pump was a Briggs and Stratton kit #193473GS, and did not have the wet bearings of the original. It bolted right up to the bottom of the engine and works like a charm.. It took a little cleaning with Gum-out to get the engine running, but now it works fine.
I remember that there was a drain plug on the side of the pump shaft housing, but nowhere in the service manual did it tell you what weight oil went in there ,or how much.

What is the best way to clean an engine?

planning f

I have a 2001 Honda Accord and the engine is getting a little dirty. I want to clean it. I know that i shouldnt take a pressure washer to it cause certain parts you do not want to get wet. Whats the best way to clean it?

Answer
go to parts store, by some engine degreaser, it comes in a big aerosol can, with the engine cold, spray it on nd let it sit for about 10-15 minutes, either with a water hose or a pressure washer rinse it off.
using a pressure washer wony hurt anything as long as you dont get too close to actually break plastic parts, or blow stuff off. also if you use hose or pressure washer, make sure you dont spray water into carb or throttle body.

Powered by Yahoo! Answers

is it a good idea to pressure wash vinyl siding?

pressure washer 2500 psi image

sunshine23

I want to know is there any danger to pressure washing vinyl siding to the house's structure.

Answer
i have been pressure washing my home for 12 yrs, this is my opinion for a larger home like bigger than 2600 sq ft.,, although all of the comments were correct about the water getting underneath the siding an into the structure. it ill not be an outstanding amount which on a good day will probably dry within an hour of spraying. ok with that said this is what i recommend. wet the entire surface area of the vinyl with water, and with a pump sprayer, mix you a solution of water and simple green, if its really dirty go with a stronger mixture or full concentrate, its not gonna hurt it a bit. spray it on let it soak for a few minutes, and wash it off with the pressure washer. now on the north end of your home, most will collect some algae and mite need more convincing, so if this is a problem an the simple green doesn't take it off, then a mild household bleach solution will probably be your best bet to get that off. let it soak a few minutes also, oh and don't where any decent clothes you do not want to ruin while spraying, they will fade and leave bleached spots if you get it on you...lol, oh yea and have some splash proof goggles on while spraying any mixture from your sprayer, don't need that stuff in your eyes...ok so i want to add..if you use a strong bleach solution, you make fade your vinyl in time.
2500 psi pressure washer...anymore pressure than this may cause vinyl damage if you put the tip too close
2-gallon sprayer
always try to spray your vinyl from the top down, that is how its designed to shield the water in the first place, although you cant do this in every application, spraying from the bottom up is fine as well don't worry it will dry out...now you may need to scrub a few stubborn areas if your home is really dirty, but if you let the simple green soak enough you may not require any scrubbing.

if your home is not that large, you may consider the simple green and a soft bristle brush and just the water hose will be sufficient. it may take you alot longer, but any case, just make sure you wet your vinyl before spraying any cleaning solution on it.
and also do not consider mixing any other cleaning solutions with the bleach.....good luck!

What is the minimum PSI I should look for in a pressure washer when using to strip paint from a wood fence?

theplaneti

I have to go cheap on this so it looks like i'm going to be getting an a electric one. I saw a Black and Decker one that said 1600psi but a review said it normally is about 1250psi and not too good at removing paint. I have seen several Karthers at advertised 1400psi without that review. I also saw a 1500psi but forgot the brand name of it.

Answer
2500 PSI should do it, be extreamly careful not to gouge or cut the wood with the spray. Also you will need to let the wood dry for at least a week , of hot dry weather, so the paint will not peel off later. Do not be disapionted if you can't remove all of the paint, you will need to scrape and sand prior to priming. Good Luck!

Powered by Yahoo! Answers

Is it ok to run a Craftsman gas powered pressure washer in the rain?

pressure washer gas image

ed g

Just bought a Craftsman pressure washer. Gas powered. Briggs & Stratton engine. I believe it's a 190cc. Using it on a huge fence and deck. Forecast is for rain for the next few days. Really want to get the job done. Rain doesn't bother me, but is it bad for the motor?

Answer
The heat produced from the device running is enough to evaporate any moisture it comes in contact with, ie, light rain storm, inadvertant spray.

is it okay to use reclaimed water in a gas pressure washer?

westpalmha

Have a fairly large gas pressure washer and wonder if using reclaimed water to wash the sidewalks would damage it?
Our neighborhood has reclaimed water available to each home for irrigation. A lot of areas in Florida use it for residential applications.

Answer
No there are no particles of matter in the water just waste treated potable water what I was told, I was also told it was controlled for irrigation and restricted for public use soooo where are you getting the reclaimed water from lol Isn't that like county and should be monitored? jk I can care less Enjoy. I just realized you ask two different questions lol. No Damage /Yes ok.

Powered by Yahoo! Answers

What size pressure washer is good for cleaning a deck?

pressure washer concrete cleaner image

BigRed

Hi i am looking at buying a pressure washer to clean my deck and to clean my house i found a 2600psi for $299 and a 3000psi for $399 both have a Honda motor. I was planing on using it to clean a couple other houses and decks is it better to get the bigger one or should i stick with the 2600psi?

Answer
The cleaning power is roughly proportional to the PSI rating multiplied by the GPM. While the higher pressure might not be necessary for the tasks you are considering, the added cleaning power means you'll get the job done faster with the more expensive unit. Keep in mind that you can always add distance to reduce pressure (back away from the surface), but you can't add pressure that the unit doesn't produce.

I have tried to use an old 1500 psi unit that I already had to clean a concrete driveway, but just purchased the 3000 psi machine from a home store, and the difference is amazing. My evaluation was that the extra $100 above the 2600 psi unit was well worth the hours saved. And the Honda engine gets very good reviews from most of what I've read.

I would suggest also getting the surface cleaning attachment, particularly for your wood deck. It's not really powerful enough for a really dirty concrete drive, but would surmise that it is sufficient for the wood (you don't want that high of pressure for the wood). For cleaning concrete surfaces, I highly recommend the Turbo nozzle; it takes the 0 deg pattern and spins it in a 15-25 deg (or so) pattern so that you get the dislodging pressure of the 0 degree, but in a pattern size that allows efficient cleaning.

Can I use a pressure washer to clean my concrete in-ground pool?

ochodemadr

I want to prepare my pool with a pressure washer then acid wash pool and paint the pool.

Answer
Realize that you will be taking a risk if you do this yourself, you will save some money but the risk just might not justify it.
If you do it be careful, follow the advice the person before me gave and keep the washer on fairly low.

IN regards to acid washing the pool... do you know how to do this? It can really be dangerous. Make sure that if you decide to do it you have someone else out there to watch you and make sure you are alright. In my opinion the fumes from the poured acid are more dangerous to you then the acid burning you. If you get acid on you just b calm and wash it off with the hose but if you start having a hard time breathing get out of the pool! You do not want to pass out in a pool coated with acid...

My advice, whether you are in Las Vegas or not, is to find a reputable company to di it for you.

Powered by Yahoo! Answers

I need help turning on a pressure washer?

pressure washer electric image

Baked Toas

Sorry for the vague description but I got a call from a friend asking for help. Here is what he said to me:

It is an electric pressure washer with an on off switch on the device itself, and a reset and test button on the power plug. He doesn't have a manual so he is following the directions on the plug (press reset, power must be on, press test, power must be off) but it doesnt work...Can any one help him out?

Answer
These are usually very simple to operate;
1) Connect and turn on the water
2) Plug in the power.
3) Check that the power plug is ON
4) Turn ON the switch on the pressure washer.
5) Squeeze the trigger. This should start the washer.

If nothing happens, check that there is power at the electrical outlet.
If you have power, and still no water pressure from the trigger, then probably some thing is defective.

What is a good pressure washer for cleaning decks/patio?

Trev

I am interested in purchasing a pressure washer that is durable, reliable, and can clean wood surfaces without damaging them. Gas or electric which would be able to perform the job with minimal effort

Answer
Sam's club or walmart ene can damage wood if you hold it in one spot to long .you need a small electric one.you can also rent from a rental center

Powered by Yahoo! Answers

How do you get tire marks off of pavement?

pressure washer 8 hp image

Q. Me and a friend have community service for leaving the black marks and they said we would probably have to clean the black marks up Please help

Answer
Pressure Washer System, I used a Honda pressure washer system with 8 hp, it takes good gas, but works. Also added special cleaning chemicals that go into the system from Home Depot.

how much hp does a 150 cc motor typically produce.?

Q. I have a 150 cc moped motor and want to use it to power a generator and a pressure washer pump.
I was wondering if it would be enough power to run them.

Answer
You need to know the generator and a pressure washer pump capacities and power requirement. I agree with answer above me for 8-10 hp.

Powered by Yahoo! Answers

Water Hose to pressure washer quick attachment?

pressure washer mi-t-m image

Richard

I'm looking for the quick attachment that goes from the pressure washer to the water hose. My Pressure washer is the (Briggs & Stratton "chore master" > Model CV-2100-OMBC). I'm not sure if I'm looking at the wrong parts or what but everything I find doesn't work for my hose. Please help.

Answer
Although the engine is a Briggs & Stratton the pressure washer was manufactured by a different company. We would recommend contacting the manufacturer of the pressure washer; Mi-T-M. They will have the information on what size fitting the pressure hose is.

Best Pressure Washer Setup for Less Than $300?

I'm looking for a pressure washer that I can use for cement driveways, decks, etc. I also am looking to get a flat surface cleaner. I have tried looking on the Costco since I heard they sold some website but I couldn't find them. I also don't want a junk piece of plastic. Thanks for the help.

Answer
You won't find a commercial grade pressure washer for less then $900. Anything with a pump that mounts underneath the motor is considered a home owner use pressure washer and won't hold up to consistent use. Plus when they do breakdown, they are more expensive to fix than what you paid for them.

Grainger sells Mi-T-M, which is a quality pressure washer. Home Depot's sells a high end Dewalt pressure washer with a Cat Pump.

Do research and talk to your local pressure washer distributor to make sure you get a quality machine.

Ben
Great Lakes Cleaning Systems

Powered by Yahoo! Answers

Can someone help me find a good hot water pressure for business?

pressure washer deals image

ol'E

looking to start P.W service on a budget but want to get some good equipment have looked at landa,and hotsy great machines but a little pricey also need surface cleaner extension wands and chemicals I got a budget of $6500 for P.W and surface cleaner wands hoses and hose reels located in alabama but will travel a bit for good deals any pro out there help me out I need it.

Answer
ol'E, I don't have any answers for you but, have you done much power washing before? It's hard work. I know I wouldn't want to do it for a living. Just yesterday, I rented a power washer and cleaned all the brick & concrete in the front yard & around both sides of my dad's house. It took me 7 hours & by the time I was done, my booty was thoroughly kicked. It looks great though. (LOL) Good luck.

Bug shit on my house vs a pressure washer?

Boredom

I have these tiny black dots on my siding, which have been multiplying over the years, and I just know it's bug shit. Got out my power washer and can blast off most, but not all. I thought about vinegar but that would destroy my my power washer I'm pretty sure.

Has anyone had to deal with these little turds on your house? HA HA! I'm going to coat my house in poison when I get the turds off.

Answer
They make a washing liquid just for siding, even aluminum siding. Check with your local hardware store. Get one of those extendable poles and a painters tray to hold the liquid that you mix with water. Then just wash instead of painting your house. After you wash an area spray the stuff off. You can wrap an old sock or towel around the end of the pole to hold the liquid and act as a scrubber. Have fun.....

Powered by Yahoo! Answers

Pressure washers? I have an opportunity to purchase an electric one. Are they as good as the gas and oil ones?

pressure washer 600 psi image

shotsofnat

It's a Karcher electric pressure washer. It has 1,600-psi. What does psi stand for? I've always been told that if you are going to buy a pressure washer it has to be gas and oil and it is usually over a 100 dollars for a good one. This one is $80.00. Should I buy it?

Thanks.
I want to use it for cleaning the side of the house and general maintenance of my home: patio, sidewalk, etc. etc...

Answer
You bettter grab this one fast... I have the same kind and I paid $180 It works great. but you have to be careful to not go exactly in the crack because it will go up under the shingls or the siding... It works great on the deck too.. After you have done the deck.... and it has dried paint it with a good coating of wood preservative.... good luck Grant M in Pennsylvania

buying a power wash,how much it realy cost?

Douglas P

Hi,
I have a cleaning services business i will start also window cleaning and power wash cleaning, so a i need a power wash and my cosin has one Karcher 4000 PSI Gas Pressure Washer #G4000SH with is grate and runs and looks nice he is not using it any more and he ask me $600$ it need only a gun extension.
i look at ebay and amazon and the same machine is around $850 to $899(on sale).
i realy apreciate all help especialy from experts.

thank you!

Technical Details:Karcher 4000 PSI Gas Pressure Washer #G4000SH
4,000 psi gas-powered pressure washer with 13 hp Honda GX series engine
For heavy-duty cleaning jobs
Features high-performance commercial-grade pump with brass pump head
Includes stainless-steel wand, 50-foot hose, and full set of Quick Connect nozzles
75 pounds

thank you all

Answer
I have a cleaning business and pressure wash frequently. That sounds like a good price but make sure that the engine is Honda. I have two pressure washers and Honda will last forever. My 4000psi was 900 brand new. Good luck to you.

Powered by Yahoo! Answers

Where does the thermal relief valve go on a Honda Excell XR2600 Pressure washer?

pressure washer pump parts image

Greg

I have a 5hp Honda Excell XR2600 pressure washer. I talked to the reps on the phone and they told me it was the thermal relieve valve was the problem I was having. It would make pressure sometimes and then othertimes not. I got the part 16484 and I just don't see where it goes. I have had the pump off and I still don't see where it goes. Any help would be appreciated.

Answer
I'm afraid the rep may have mislead you. The thermal relief valve only activates if the pump over heats by releasing hot water from the pump to make room for cooler water. It does nothing for making pressure. The pressure problem you describe would be connected with either the pressure relief valve, or the pump valves, or both.

Type of oil required for pressure washer pumps?

Al

I have a 3500 psi simpson pressure washer. Bought in 1997 but hardly used. What type of oil does the pressure pump requires? Although I did not use it more than 30 hours but the oil level seems to be low.
Thanks,

Answer
I use straight 30 weight, but the link below suggests a special blend for the manufacturers motor.


".... and made a visit to the local Napa Auto Parts store looking for oil. The guy told me to use 30 weight Non-Detergent oil. He said heâs worked with many a pressure washer and they all took the same oil."

Powered by Yahoo! Answers

Is there a tool I can attach to my pressure washer nozzle that will maintain a consistant distance?

pressure washer attachments image

izmondo

Something that would roll on two wheels maybe. I've seen the type called water brooms, not really what I'm looking for. I'm looking for an attachment for my existing gun nozzle. Something that would make cleaning my deck more efficient.
I found an item similar to what I mean here :
http://deckaidmadesimple.com/products.htm

Answer
Well you could spend like 80 bucks and buy a used one of those pressure things. They are crazy strong and get whatever the heck they hit clean. Here is a sight with a picture of one (it is like really expensive):
http://www.pressurewashersdirect.com/

What Pressure Washing equipment do you need to Pressure Wash?

DanjoHart

I want to start a pressure washing service. What equipment do I need besides my very nice commercial quality electric air compressor and air hoses?

Do I need a wand / water attachment?

I also will get insured and bonded.

Thanks for help in how I should "gear up".

Answer
You should pick up a few gas powered pressure washers, & maybe down the road, a large portable water tank

Powered by Yahoo! Answers

I would like to purchase a 2000 psi or more pressure washer. Does anyone have one for sale?

pressure washer warehouse image

mr_attenti

Answer
I don't know if you live near a Sam's Warehouse but I was in ours today and they had a 2800 PSI with a Honda engine for $258.

Honda makes a good engine. Nothing like a Briggs. I almost bought one just because the price was so good.

What is the part called that holds a pressure washers wheel on?

TylerK

I have to replace wheels on a pressure washer. The axle is 3/4" . I just ordered the wheels online, but I need to find the part that holds the pressure washer wheels on the axle. I only have one part and the one I do have is round. I.D. is 3/4" O.D. is roughly 1 1/2" x 1/2" wide. And there is allen wrench nut you tighten to hold it against the axel obviously, so the wheels don't fall off. I was looking at a pal-nut, thinking I could just bang it on and it would work. Maybe? Do they sell those at Home Depot? Anyone know what I am talking about or the name of the part I am looking for? Anyone... If so point me in the right direction and help me get this problem fixed. Thanks

Answer
Go to Any bearing shop and tell them you need a locking Collet bring the shaft to get one that will fit, they have them with one two and three locking screws but one should work fine. Places like King Bearing or go to a auto parts store and ask them if they know anywhere in your area to buy them. You can also get them at electrical warehouses too.

Powered by Yahoo! Answers