How can i tell what pressure my pressure washer is at?

N/A

I have a 3800 psi dewalt pressure washer and im wanting to turn it down to about 3000-3300 psi but im not sure to tell what psi im at while turning the pressure down.
If anyone could help me out id appreciate it!
Thanks!

Answer
What you would have to do is connect a pressure gauge between the end of the hose and the gun. Run the pressure washer with the gun's trigger pressed so there's water flow and check the pressure it is shooting water. To adjust it to the pressure you want you can either use the unloader to regulate pressure or adjust the engine's rotation which would also regulate pressure.
If you need a gauge here is the link to a 5000 psi one. There are more on the website in case you think this one is too much.
http://www.roncoshop.com/GAUGE_KIT_5000_PSI_85305001_p/85305001.htm

Pressure test failed, plumbing?

Roni

We are going to buy a foreclosed home. On condition report , it says pressure test failed and washer connector broken. Bank wont allow us to turn on water to inspect for leaks. Is this a risky buy, since we cant test plumbing. Is there any other good way to test the plumbing? what could worst happen if the pressure test has always failed?

Answer
If you have an air compressor you can hook it to one faucet, Put a pressure gauge on another faucet and open both faucets to pressure check the system. Once the compressor shuts off (system pressurized) close the faucet with the compressor and watch the pressure gauge to see if it holds it's reading. If it drops you have a leak. With air in the system leaks can be detected by using a spray bottle of soapy water to spray connections. Leaky connections will make bubbles.

Powered by Yahoo! Answers

How can i tell what pressure my pressure washer is at?

pressure washer gauge image

N/A

I have a 3800 psi dewalt pressure washer and im wanting to turn it down to about 3000-3300 psi but im not sure to tell what psi im at while turning the pressure down.
If anyone could help me out id appreciate it!
Thanks!

Answer
What you would have to do is connect a pressure gauge between the end of the hose and the gun. Run the pressure washer with the gun's trigger pressed so there's water flow and check the pressure it is shooting water. To adjust it to the pressure you want you can either use the unloader to regulate pressure or adjust the engine's rotation which would also regulate pressure.
If you need a gauge here is the link to a 5000 psi one. There are more on the website in case you think this one is too much.
http://www.roncoshop.com/GAUGE_KIT_5000_PSI_85305001_p/85305001.htm

Briggs and Stratton engine wont start?

goodnused

Asking this question for a friend. He said that the engine acts like it is not firing or getting spark. He replaced the spark plug, also checked the air gap on the magneto...still nothing, he said. Wants to know how much compression the engine should have with a regular automotive Compression gauge? Could the engine be "OUT OF TIME" or have a broken key way??? The engine is on a pressure washer....about 3 years old. CRAFTSMAN. Any ideas would be helpful. Wouldn't fire or try to start using Starting Fluid also, so he doesn't think it is a fuel problem. Thank you for any suggestion or help in advance.

Answer
Briggs & Stratton does not rate the compression of the engine, we recommend the use of a leak-down tester. As for the engine not starting, the most likely issue is a clog in the carburetor. The carburetor should be overhauled and cleaned. After that you can check the flywheel key to see if it has been sheared. Then check the spark plug wire on the magneto and that it is connected properly.

Powered by Yahoo! Answers

My oil pressure warning light on my Honda Accord 96 goes on when the engine is idle, what is the problem?

pressure washer gauge image

globalspec

I have an accord 96 that has 100,000kms on it. had an oil change recently.

A few days after this oil change, I had an overheat and after this overheat, the oil pressure warning light started acting eratically.

First, after a cold start, the light does not turn on but after the engine warms up, the light flashes. The problem is, while revving the engine, the light goes off and immediately goes on again when the engine is idle.

To address my original problem, mechanics informed me that they would change the oil sending unit, change thermostat valve and thermostat switch.

After this, the problem was still the same (light goes off with revving). They recommended a general overhaul for the reason that the engine had so much sludge and they blamed the problem on the engine flush that was included during the change oil.

Now, i really dont know what to do next. General overhaul is too expensive for my budget.. Any tips?
Thanks very much!

Answer
the first and obvious question is--have you checked the oil level recently? I've seen drain bolts leak on Hondas if you don't change the washer for the plug and you could legitimately have a low oil condition. so thats the first thing to do.

then, if the oil is full, have your technician put an oil pressure gauge on the car to run a pressure test. That will tell you if the problem is a mechanical one (oil pump) or an electrical one (sending unit/gauge). Your description sounds like a mechanical problem with the oil pump. If the car does have low oil pressure, then the next thing to do is to have the oil pan removed to check the oil pick up for the oil pump. If it is clogged they can clean it. If not, then you'll have to change the pump.

accords are not known to generate a lot of sludge unless the oil is never changed. the engine flushes rarely provide any value.

hope that helps

My 11 HP pressure washer is rated 3400 psi. When I put a gauge on it, it only reads 3000psi !?

tonymonton

It is a Craftsman (Briggs and Stratton) 11HP, 3400psi, 4.0gpm rated machine. I only used it a few times since I bought it new. Is Sears exaggerating the specs?

Answer
3000 kicks but, oh well!

Powered by Yahoo! Answers

My 11 HP pressure washer is rated 3400 psi. When I put a gauge on it, it only reads 3000psi !?

pressure washer gauge image

tonymonton

It is a Craftsman (Briggs and Stratton) 11HP, 3400psi, 4.0gpm rated machine. I only used it a few times since I bought it new. Is Sears exaggerating the specs?

Answer
3000 kicks but, oh well!

Should I use new bolts having an oil pan gasket replaced?

AsiaGurl

I'm having my oil pan gasket replaced on a 1999 Buick Lesabre 3800 Series II 3.8L. Should I have them reuse the same bolts or get new bolts? If so anyone know what size the bolts are?

Also, will the job involve lifting the engine or removing the alternator? What is a good price and how many hours of work.

I have a slow leak(1/4 quart every 1,000 miles) on the bottom and the oil pressure gauge dances around with 50-60 pressure.

The oil leak has caused 3 starters to fill up with oil and the bottom motor mount is soaked in oil. All the gaskets on the top have been replaced.

Answer
No but if it jas lock washers id replace those. And dont forget to torque them to spec.

Powered by Yahoo! Answers

How can i tell what pressure my pressure washer is at?

pressure washer gauge image

N/A

I have a 3800 psi dewalt pressure washer and im wanting to turn it down to about 3000-3300 psi but im not sure to tell what psi im at while turning the pressure down.
If anyone could help me out id appreciate it!
Thanks!

Answer
What you would have to do is connect a pressure gauge between the end of the hose and the gun. Run the pressure washer with the gun's trigger pressed so there's water flow and check the pressure it is shooting water. To adjust it to the pressure you want you can either use the unloader to regulate pressure or adjust the engine's rotation which would also regulate pressure.
If you need a gauge here is the link to a 5000 psi one. There are more on the website in case you think this one is too much.
http://www.roncoshop.com/GAUGE_KIT_5000_PSI_85305001_p/85305001.htm

How do i find out how much psi my pressure washer is putting out when i go to adjust the pressure on it?

Adam Mcbri

i have a 4000 psi pressure washer and 3.5gpm. but i wanna know how much pressure i am putting out when i adjust it. do i add a gauge somewhere????

Answer
You asked a question without listed the unit model and style ?

If it don't already have a gauge its 4000psi all the time what changes the strength is the nozzle heads
without knowing which one of the millions of pressure washers you have no one can answer your question

hope it helps
Lr

Powered by Yahoo! Answers